Cooling tower infill
  • Hot
    Marley MX75 cooling tower infill for crossflow cooling tower fill

    Marley MX75 cooling tower infill for crossflow cooling tower fill

    Marley MX75 cooling tower fill for crossflow cooling tower infill is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting the maximum exposure to air flow. This cooling tower fill provides much more water surface exposure per cubic foot than the splash type fill. Marley MX75 cooling tower fill for crossflow cooling tower infill is thermoformed from PVC with a flame spread rating less than 25 per ASTM E-84 and is considered self-extinguishing. Therefore, the risk of fire damage is minimal.

    Send Email Details
  • Hot
    SNCS Fill For Counter Flow Cooling Towers

    SNCS Fill For Counter Flow Cooling Towers

    The Cooling Tower PVC Filler is probably the most thermally efficient fill worldwide, has proven its efficiency for more than 30 years. The sharp horizontal corrugations of cooling tower PVC filler allow even water redistribution on the sheet and water rotation for good contact with air. The offset flute design allows vertical rotation of air with limited pressure drop. This type of cooling tower fill well adapted to any induced draft or natural draft cooling tower using normal industrial water quality.

    Send Email Details
  • Cooling Tower Fill Film

    Cooling Tower Fill Film

    The fills are suitable of any induced draft or natural draft cooling tower using normal industrial water quality. Sharp horizontal corrugations allow even water redistribution on the sheet and water rotation for good contact with air. The offset flute design allows vertical rotation of air with limited pressure drop. Hanging design type or glue sticked type are available.

    Send Email Details
  • High temperature resistance cooling tower net splashing fill

    High temperature resistance cooling tower net splashing fill

    High temperature resistance cooling tower net splashing fill have been specially designed for medium to strongly polluted cooling water, it focus of the development being on a high stability as well as on easy and economical installation. Therefore these fills are built from mechanically joint grids and are easily cleaned. Features: 1) Products suitable for inferior water qualities 2) Chemical and high temperature resistance of Polypropylene 3) High stability 4) Cleaning with high pressures cleaners possible 5) Long service life 6) Impact resistant 7) Environmentally friendly 8) Economical installation

    Send Email Details
  • Cooling Tower Splash PVC Fills

    Cooling Tower Splash PVC Fills

    This type cooling tower fill is for BAC VXT/VTL Cooling towers, can guaranteed original performance. Easy to handle, lift, dismantle and rebundle; Easy core inspection: by bundle and by sheet; Easy to clean; Reducing fouling;

    Send Email Details
  • Hot
    PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment

    PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment

    This PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is used in deposition and discharging sand. Recently, it is very popular in the drain aging project. With widely applicability, high efficiency, small proportion, PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is very suitable not only in discharge, deposition of water from daily life and industry isolation of oil, but also in the project which is being constructing, re-construction of project.

    Send Email Details
  • Cooling Tower PVC Sheet

    Cooling Tower PVC Sheet

    The pvc sheet is the material of cooling tower fill, which is made by the raw mateial is PVC resion. The max. width is 1700mm, and the sheet thickness can from 0.25mm to 0.40mm.

    Send Email Details
  • Crossflow PVC film for cooling tower infill

    Crossflow PVC film for cooling tower infill

    Crossflow PVC film for cooling tower infill is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting maximum exposure to thevair flow. This type of fill provides much more water surface exposure per cubic foot than splash type fill.

    Send Email Details
Get the latest price? We'll respond as soon as possible(within 12 hours)

Privacy policy