The fills are suitable of any induced draft or natural draft cooling tower using normal industrial water quality.Send Email Details
Sharp horizontal corrugations allow even water redistribution on the sheet and water rotation for good contact with air. The offset flute design allows vertical rotation of air with limited pressure drop.
Hanging design type or glue sticked type are available.
High temperature resistance cooling tower net splashing fill have been specially designed for medium to strongly polluted cooling water, it focus of the development being on a high stability as well as on easy and economical installation. Therefore these fills are built from mechanically joint grids and are easily cleaned.Send Email Details
1) Products suitable for inferior water qualities
2) Chemical and high temperature resistance of Polypropylene
3) High stability
4) Cleaning with high pressures cleaners possible
5) Long service life
6) Impact resistant
7) Environmentally friendly
8) Economical installation
This type cooling tower fill is for BAC VXT/VTL Cooling towers, can guaranteed original performance.Send Email Details
Easy to handle, lift, dismantle and rebundle;
Easy core inspection: by bundle and by sheet;
Easy to clean;
Counterflow Cooling Tower Fill is qualifided worldwide as the best film fill combining low fouling properties with good thermal performance.And the fill sheets can be glued to block or suspension by rod.Send Email Details
It is adapted to counterflow cooling tower normal using quality industrial water.It is also suitable for other severve application,such as lamin]ated decanting and washing gas.
This PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is used in deposition and discharging sand. Recently, it is very popular in the drain aging project.Send Email Details
With widely applicability, high efficiency, small proportion, PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is very suitable not only in discharge, deposition of water from daily life and industry isolation of oil, but also in the project which is being constructing, re-construction of project.
Crossflow PVC film for cooling tower infill is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting maximum exposure to thevair flow. This type of fill provides much more water surface exposure per cubic foot than splash type fill.Send Email Details
PVC Filler Round Type Cooling Tower is heat-elimination in the cooling towers. It is a crucial component in the exchange of waterflow and gasflow process in the cooling tower.Send Email Details
PVC Filler Round Type Cooling Tower is manufactured from PP or PVC sheets which are solvent-welded for maximum strength and resistance to organic and inorganic solvents, rot, fungus, UV, alkalis, acids and chemicals that are usually present in water.
PVC Filler Round Type Cooling Tower has a unique design for counterflow round type cooling tower which is its most popular heat eliminating medium.
Cross Cooling Tower PVC Filling Material plays a crucial role in improving the lifespan of the cross flow cooling tower. It also could increases the water flow process remarkably for better performance and efficiency as well.Send Email Details
This cross flow cooling tower PVC filling material is glued together by A type and B type sheets to be a block which is stalled in tower.
This PVC fill use the modified PVC sheet and is manufactured with a unique modified formula to enable strong resistance and guarantee its durability. It involves special processing whereby the inner side edge is integrated with a liquid baffle plate which controls the drift loss of water.
LATINO-9615 Cross-Fluted high-density film fill desinged for cooling of power plant, petrochemical HAVC and other process cooling towers.Send Email Details
The fill shall be fabricated from regrid, corrugated PVC sheets and are conducive to cooling water and UV protected.
The media modules shall be fabricated from PVC sheets of quality stated above and completely corrugated at an angle of 60 degrees from the horizontal to form a cross-corrugated pattern between adjacent sheets providing a continuous and horizontal redistribution of air and water. The flute height for each corrugation shall be 20mm.
S wave corrugated PVC cooling tower fill is the most widely used cooling tower fill. Due to its big space design, and S wave shape, The fills have excellent cooling efficiency and good performance in processing the dirty water, especially the processing water contains solid impurities.Send Email Details
The "S" wave cooling tower fill packs made by PVC or PP material, thermal forming by mold and plastic forming machine. Sheet thickness and color can be customized. All these advantages makes its become the ideal infill for counter flow industrial cooling tower, Power plant heave duty cooling tower,ewage treatment cooling tower and so on.
Durable crossflow cooling tower PP infill replacement is made by PP material. It is much durable than the cooling tower PVC fill.Send Email Details
Cooling tower PP fill is used in the counterflow cooling tower, this cooling tower infill also could been made by PVC material.