-
Hot
12mm Sheet Pitch Cooling Tower Infill For Counter Flow Cooling Tower Fills
This counterflow cooling tower fill is used in:
Send Email Details
- TSS is less than 100 PPM with good microbiological control (less than 25PPM where microbiological control is poor);
- Make-up from uncontaminated sources
- Water treatment using oxidizing biocides & scale inhibitors
- Low cycles of concentration
- Minimal airborne dust
- No potential for oil or grease contamination -
Hot
Cooling tower PP fill manufacture with high temperature resistance
The Net fill (Non-glued assembly fill) have been specially designed for medium to strongly polluted cooling water, it focus of the development being on a high stability as well as on easy and economical installation. Therefore these fills are built from mechanically joint grids and are easily cleaned. The Net grid packings are high-performance fills which provide an optimized pressure drop.
Send Email Details
Features:
1) Products suitable for inferior water qualities
2) Chemical and high temperature resistance of Polypropylene
3) High stability
4) Cleaning with high pressures cleaners possible
5) Long service life
6) Impact resistant
7) Environmentally friendly
8) Economical installation -
Hot
Cooling Tower PVC Film Fill For Counter Flow Cooling Towers
The Cooling Tower PVC Filler is probably the most thermally efficient fill worldwide, has proven its efficiency for more than 30 years.
Send Email Details
The sharp horizontal corrugations of cooling tower PVC filler allow even water redistribution on the sheet and water rotation for good contact with air. The offset flute design allows vertical rotation of air with limited pressure drop.
This type of cooling tower fill well adapted to any induced draft or natural draft cooling tower using normal industrial water quality. -
955mm* 705mm Cooling Tower PP Splashed Grid Fill
The grid fill is the result of an extensive optimization of the lath width, the blockage area ratio and the lath layout;
Send Email Details
The water droplets, splashing on a well drained lath, break in a large number of very small droplets, inducing large heat exchange surface. Blockage area ratio and lozenge layout is the optimized compromise between the pressure drop and the probability of large droplets to hit the laths.
The laths height has been selected to transfer the load to the supporting spacers using minimum material quantity.
It may be used as well in Counterflow as in Crossflow cooling towers, mechanical or natural draft.
It is well adapted to any water quality, even without water treatment, when the fouling risk cannot be determined, in particular with seawater -
820 mm Width Marley Type Mx75s PVC Fill for Cooling Tower
820 mm Width Marley Type Mx75s PVC Fill for Cooling Tower is with cooling tower air inlet louver and drift eliminator.
Send Email Details
And its installation method is gluing and hanging according to the customer's request.
Material: PP and PVC -
High Efficiency MC75 Cooling Tower Infill
MC75 is a film fill system designed for counterflow towers offering you several distinct advantages.
Send Email Details
Crossed corrugations provide the surface area and turbulence to develop efficient heat transfer. The corrugations inherently establish uniform fill sheet spacing at 0.75”.
MC75 fill is thermoformed from .015” thick, UV inhibited, chemically resistant polyvinyl chloride (PVC). The flame spread rating is less than 25 per ASTM E-84 and is considered self-extinguishing. -
Hot
BAC CF1200 New Type Non-Glued Counter Flow Cooling Tower Fill
This BAC CF1200 New Type Non-Glued Counter Flow Cooling Tower Fills is used in:
Send Email Details
- TSS is less than 100 PPM with good microbiological control (less than 25PPM where microbiological control is poor);
- Make-up from uncontaminated sources
- Water treatment using oxidizing biocides & scale inhibitors
- Low cycles of concentration
- Minimal airborne dust
- No potential for oil or grease contamination -
Hot
Mx75 Cross Flow Cooling Tower PVC Fills
The cooling tower fill is widely used in crossflow cooling tower and also for Marley cooling tower fill replacement. MX75 is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting maximum exposure to air flow.
Send Email Details
This type of cooling tower fill provides much more water surface exposure per cubic foot than splash type fill.
The fill incorporates highly efficient cellular drift eliminators, integrally molded within the fill sheets. Compared with previous designs, these eliminators reduce drift emissions from the tower by a factor of ten or more! Less drift means tower owners save water bills and water treatment chemical expenses. -
Hot
L3000*H2000*T150 7090 evaporative cooling pad with aluminium alloy frame for poultry farm
Plastic evaporative cooling pad, high absorbability, high water resistant, anti-mildew and long service life.
Send Email Details
Large evaporation area, cooling efficiency as high as 78%.
The cooling pad absorbs water naturally, with fast speed of pervasion and lasting effectiveness. One drop of water can diffuse within 4~5 seconds. The natural absorption height is 60~70mm/5minutes, as 200mm/1.5 hours, having reached international standard.
The cooling pad does not contain phenol which is irritant to the skin and the like chemical products. It is safe, energy saving, environmental protective, economic and durable. -
BAC CF1200 New Type Non-Glued Conter Flow Cooling Tower Fills
This BAC CF1200 New Type Non-Glued Conter Flow Cooling Tower Fills is used in:
Send Email Details
- TSS is less than 100 PPM with good microbiological control (less than 25PPM where microbiological control is poor);
- Make-up from uncontaminated sources
- Water treatment using oxidizing biocides & scale inhibitors
- Low cycles of concentration
- Minimal airborne dust
- No potential for oil or grease contamination -
Hot
Ebara Cross Cooling Tower PVC Fill Material For Ebara Cooling Towers
Cross Cooling Tower PVC Filling Material plays a crucial role in improving the lifespan of the cross flow cooling tower. It also could increases the water flow process remarkably for better performance and efficiency as well.
Send Email Details
This cross flow cooling tower PVC filling material is glued together by A type and B type sheets to be a block which is stalled in tower.
This PVC fill use the modified PVC sheet and is manufactured with a unique modified formula to enable strong resistance and guarantee its durability. It involves special processing whereby the inner side edge is integrated with a liquid baffle plate which controls the drift loss of water. -
Hot
Cross Flow Cooling Tower PVC Fill Used For Marley Cooling Towers
This MX75 cooling tower fill virtually eliminates the nuisance caused by drift spotting on adjacent buildings and property. For additional savings, the drift eliminators discharge air directly toward the fan. Discharge air, traveling in the right direction when it leaves the eliminators, translates to lower fan horsepower.
Send Email Details
