cooling tower
-
Air-Cooled Condensers Fan Stack
The Air-Cooled Condensers Fan Stack is made by two method, hand lay-up and and SMC. You could choose these two different producing method based on your requirement. For these two methods, the final effect is the same. The hand lay-up method is glue the water-resistance resin with the high quality fiberglass reinforcement by hand. So it is durable. For the SMC method, the FRP fan stack is produced by mould. The production time is shorter than hand lay-up. And the price is lower too.
Email Details -
Plastic Spray Nozzle For Cooling Tower
This plastic spray nozzle for cooling tower is made from ABS material. It has no internal parts as other nozzles. The below attached diffusion ring will not retain fibrous debris. The unique "Full cone" distribution pattern guarantee the uniform water distribution into the cooling tower fill blocks. It could provisde the uniform water distribution even near spray boundaries with minimal spray overlap. The diameter of water outlet is about 44mm, the outlet water pressure is very low water pressure and non-clogging.
Email Details -
Hot
PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment
This PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is used in deposition and discharging sand. Recently, it is very popular in the drain aging project. With widely applicability, high efficiency, small proportion, PP/PVC Lamella Clarifier/Inclined Tube Settler for Wastewater Treatment is very suitable not only in discharge, deposition of water from daily life and industry isolation of oil, but also in the project which is being constructing, re-construction of project.
Email Details -
Crossflow PVC film for cooling tower infill
Crossflow PVC film for cooling tower infill is a hanging film type cooling tower fill which spreads the water into a thin film, flowing over large vertical surfaces, promoting maximum exposure to thevair flow. This type of fill provides much more water surface exposure per cubic foot than splash type fill.
Email Details -
145MM PVC drift eliminator, air inlet louver for cross flow cooling tower
145MM PVC drift eliminator, air inlet louver for cross flow cooling tower is a Demisting device, which is used in remove numbers of small droplets drift from hot & humid air. Meanwhile, to avoid of the pollution of water mist on the surrounding environment and ice. It was widely used in domestic power plants,steel mills,oil chemical industry, such as mechanical ventilation and natural ventilation cooling tower.
cooling tower drift eliminator cooling tower eliminator cooling tower air inlet louver pvc drift eliminatorEmail Details -
Hot
Cooling Tower PVC Replacement
This type of Fill is widely used in counterflow of cooling tower in power plant, petrochemical, HVAC and other process cooling towers. The Fill have vertically offset flutes arranged in a straggered pattern with adjacent sheets providing a continuous and horizontal redistribution of air and water. The flut height for each corrugation shall be 20mm.
Email Details -
Counterflow Cooling Tower Drift Eliminators
This Counterflow Cooing Tower Drift Eliminators is made by PVC raw material, and is widly used in the cooling tower industry. The wave blade 、wave spacer and PP spacer were assembled together to been a block, and then were assembled in the cooling tower. The block size and shape could be customized according to your request. Because of its special designed type, it could reduce the water loss effectively in the extensive application in our site projector. It could been installed very easily without any tools. And it is also easier for maintance and cleaning.
cooling tower air inlet mist eliminator cooling tower drift eliminator suppliers high efficiency drift eliminatorEmail Details -
Hot
ACC Fans
ACC fans design accoring to the most advanced airfoil, ACC Fans is features is large flow, high efficiency, low noise. Once every piece of blade shaped, Latino's enginner need to make large torque measurement,to check the ACC fan meet with the design requirements. The unique aerodynamic design optimizes the performance of the blade to supply significantly lowe sound level and high efficiency.
Email Details -
Hot
Marley NS6 Cooling Tower Nozzle Condenser Spray Nozzles
Marley NS6 Cooling Tower Nozzle Condenser Spray Nozzles is suit for Marley counterflow cooling towers. It it is an other type of the Marley brand cooling tower nozzle which is a little same to NS5 cooling tower nozzle, and can replace the NS5 cooling tower nozzle. This cooling tower NS6 spray nozzle is made by PP material, which is suitable for the high temperature.
Email Details